Part Number: 74LS, Maunfacturer: Motorola, Part Family: 74, File type: PDF, Document: Datasheet – semiconductor. These 8-bit shift registers feature gated serial inputs and an asynchronous clear. A low logic level at either input inhibits entry of the new data, and resets the first. This 8-bit shift register features gated serial inputs and an asynchronous reset. The gated serial inputs (A and B) permit complete control over incoming data as a.
|Published (Last):||10 December 2011|
|PDF File Size:||13.62 Mb|
|ePub File Size:||13.20 Mb|
|Price:||Free* [*Free Regsitration Required]|
Where this voltage is coming from, I don’t know. Hello, again, and thank you all very much for your help.
The 22nF are for the switch contacts, to eliminate any electrical noise, caused by switch contact bounce. Not more than one output should be shorted at a time, and duration should not exceed one second.
Search field Part name Part description. High Level Input Current. Data at the serial inputs may be changed while the clock is high or low, but only information meeting the setup requirements will be entered clocking occurs or the low-to-high level transition of the clock input. But everybody else seems to just hook these things up, and go with it.
Since the IC is a relatively bad conductor right? I also posted this question over at Electronic Circuits eatasheet Discovercircuits. The output pin can sink or source current, check the datasheet for your IC type.
But with the inter-IC connection, I think my brain is still not in gear: If I have a shared clock signal for both the ICs which seems to be a common praticeAs stated when inputs are connected to output pins, NO pull ups. If I understood 74lls164 datasheet’s diagram correctly, there’s an AND gate on the two input pins, so I think both have to be high – but that doesn’t really matter, since I simply connected the two together. The IC is very fast so you will [ or shouldn’t] see any flicker as the SR clocks.
This 8-bit shift register features gated serial inputs and an. Media New media New comments Search media. That switch does NOT turn on the outputs – but touching that pin does.
All diodes are 1N or 1N Propagation Delay Time, Reset to Q. The mains electricity here in Costa Rica is horrendously ‘dirty’, so I wanted to eliminate that factor. Electro Tech is an online community with overmembers who enjoy talking about and building electronic circuits, projects and gadgets. That’s why am a bit mad at me for getting stuck so early on! High Level Input Voltage.
Which would cause LEDs to flicker, or other weird thins to happen, i’d guess. You must log in or register to reply here.
74LS 8-bit Shift Register IC | Jaycar Electronics
I already had the circuit soldered, and being the stubborn guy i am and because of my lack of solder-removal-wickI tried it with pull-down resistors 1k to GNDagainst all recommendations i read online. The gated serial inputs A and B permit complete control over incoming data as a low at either or both input s inhibits entry of the new data and resets the first flip flop to the low level at the next clock pulse. There could be any number of reasons why its not working, follow my instructions and we may find out why.
Now that that’s cleared up: Datasheets, Manuals or Parts. High Level Output Current.
74LS164 Datasheet PDF
A high level input enables the other input which will then determine the state of the first flip-flop. In my so-called diagram, I drew what I would have thought to be a pull-up resistor on the signal pins in red. If own of the two posts gets an answer, I will of course also post it on the other board. Maximum Ratings are those values beyond which damage to the device may occur.
All inputs are diode- clamped to minimize transmission-line effects. High Level Output Current. Low Level Output Current. Is that a good thing, or a bad thing?
Low Level Output Current. You do not require pull downs.
Setup Time, A1 or A2 to Clock. Fully Buffered Clock and Serial Inputs.