P4MM4 – read user manual online or download in PDF format. Pages in total: Biostar | P4MM4 | Owner’s Manual | Biostar P4MM4 Owner’s Manual The content of this user’s manual is subject to be changed without notice and we . P4MM4 VIA P4M gaming motherboard features-Socket ;Supports Intel Pentium 4/Celeron D/Celeron Processor;Supports FSB /MHz;Support.
|Published (Last):||28 October 2018|
|PDF File Size:||14.92 Mb|
|ePub File Size:||19.1 Mb|
|Price:||Free* [*Free Regsitration Required]|
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
There manuak no guarantee that interference will not occur in a particular installation. The vendor makes no representations or warranties with respect to the contents here and specially disclaims any implied warranties of merchantability or fitness for any purpose. Further the vendor reserves the right to revise this publication and to make changes to the contents here without obligation to notify any party beforehand.
All the brand and product names are trademarks of their respective companies. Supports Intel Pentium 4 processor up to 3. Do not support Williamate CPU. Maximum memory size is up to 2GB.
Following table is only for reference. Pull the lever sideways away from the socket and then raise the lever up to a degree angle. The CPU will fit only in the correct orientation. Hold the CPU down firmly, and then close the lever to complete the installation. This completes the installation. The fan cable and connector may be different according to the fan manufacturer.
Connect the fan cable to the connector while matching the black wire to pin 1. When connecting with wires onto connectors, please note that the red wire is the positive and should be connected to pin 2, and the black wire is Ground and should be connected to GND.
Unlock a DIMM slot by pressing the retaining clips outward. Floppy Disk Connector The motherboard provides a standard floppy disk connector that supports K, K, 1.
This connector supports the biostqr floppy drive ribbon cables.
The IDE connectors can manuao a master and a slave drive, so you can connect up to four hard disk drives. The first hard drive should always be connected to IDE1. This PCI slot is designated as 32 bits. Accelerated Graphics Port Slot Your monitor will attach directly to that video card. It will disable the output on back panel audio connectors. Remove AC power line.
Wait for five seconds.
Biostar P4M80-M4 Owner’s Manual
Power on the AC. Reset your desired password or clear the CMOS data. If the signal has been triggered, it will record to the CMOS and mwnual the message on next boot-up.
If the following message is shown after boot-up the system, it means the BIOS contents are corrupted. Make a bootable manyal disk. Insert the bootable disk into floppy drive and press Enter.
System will boo-up to DOS prompt. System will update BIOS automatically and restart. The BIOS has biosar recovered and will work properly. CPU Overheated If the system shutdown automatically after power on system for seconds, that means the CPU protection function has been activated. When the CPU is over heated, the motherboard will shutdown automatically to avoid a damage of the CPU, and the system may not power on again.
In this case, please double check: CPU p4,80-m4 is rotated normally. After confirmed, please follow steps below to relief the CPU protection function.
Biostar P4M80-M4 User Manual
Remove the power cord from power supply for seconds. Plug in the power cord and boot up the system. Clear the CMOS data. Power on the system again.
Biostar P4MM4 | P4MM4 user’s manual – Page 5
Solution No power to the system at all 1. Indicator light on keyboard does not turn on. Keyboard lights are on, power indicator lights are lit, and hard drive is spinning. Make sure power cable is securely plugged in. Using even pressure on both ends of the DIMM, press down firmly until the module snaps into place. System does not boot from hard disk 1. Check cable running from disk to disk controller board.
Make sure both ends are securely plugged in; check the drive type in the standard CMOS setup. Backing up the hard drive is extremely important. All hard disks are capable of breaking down at any time. System only boots from optical drive. Hard disk can be read and applications can be used but booting from hard disk 2. Back up data and applications files. Reformat the hard drive. Re-install applications and data using backup disks. Make sure correct information is in setup.
Call the drive manufacturers for compatibility with other drives. With the Overclock Manager, users can easily adjust the frequency they prefer or they can get the best CPU performance with just one click. The cool Amnual Monitor smartly indicates the temperatures, voltage and CPU fan speed as well as the chipset information.
Execute the setup execution file, and then the following dialog will pop up. When you see the following dialog in setup procedure, it means setup is completed. The following figures are just only for reference, the screen printed manua this user manual will change according to your motherboard on hand. Whenever the Tray Icon utility is launched, it will display a little tray icon on the right side of Windows Taskbar. Main Panel contains features as follows: With a user-friendly Status Animation, it can represent 3 overclock percentage stages: Voltage Panel Click the Voltage button in Main Panel, nanual button will be highlighted and the Voltage Panel will slide out to up as the following figure.
In this panel, you can decide to increase CPU core voltage and Memory voltage or not. Overclock Panel Click the Overclock button in Main Panel, the button will be highlighted and the Overclock Panel will slide out to left as the following figure.
Overclock Panel contains the these features: We strongly recommend you verify every speed you overclock by click the Verify button. Pop up the following dialog. Let user select a restoring way if system need to do a fail-safe reboot. Then system will do fail-safe reboot by using Watchdog function. If the testing is ok, then the current frequency will be saved into system registry.
If the testing fail, system will do a fail-safe rebooting. Hardware Monitor Panel Click the Hardware Monitor button in Main Panel, the button will be highlighted and the Hardware Monitor panel will slide out to left as the following figure.
In this panel, you can get the bjostar status information of your system. The information will be refreshed every 1 second. In this panel, you can get model name and detail information in hints of all the chipset that are related biosrar overclocking. The Setup program allows users to modify the basic system configuration.
This special information is then stored in battery-backed RAM so that it retains the Setup information when the power is turned off.
The BIOS provides critical low-level support for standard devices such as disk drives and serial and parallel ports. L4m80-m4 rest of this manual is intended to guide you through the process of configuring your system using Setup. Sleep and Suspend power management modes are supported. The following table provides more detail about how to navigate in the Setup program by using the keyboard. The Main Menu allows you to select from several setup functions.
Advanced Chipset Features This submenu allows you to configure special chipset features. Power Management Setup This submenu allows you to configure the power management features. P480-m4 Health Status This submenu allows you to monitor the hardware of your system. However, this function is strongly recommended not to use.
Biostar P4MM4 Owner’s Manual |
Load Optimized Defaults This selection allows you to reload the BIOS when the system is having problems particularly with the boot sequence. These configurations are factory settings optimized for this system.
A confirmation message will be displayed before defaults are set. You will be prompted with to enter a password.