gate instructions above, with the addition of a tee-piece (not from Turbosmart that plugs directly into the eboost2 LED output with no additional wiring. Details; Applications; Instructions; Accessories. Winner of the Global Press Award at the SEMA Trade Show, e-Boost2 allows the user to control, monitor. For advanced hook up methods, please read the complete E-Boost 2 manual. 1) Enter Setup menu by pressing MODE and SETUP/UP at the same time.
|Published (Last):||3 April 2014|
|PDF File Size:||3.33 Mb|
|ePub File Size:||2.83 Mb|
|Price:||Free* [*Free Regsitration Required]|
Discussion in ‘ Turbo Cobras ‘ started by badcobraJul 27, Eboost2 boost by gear how to Discussion in ‘ Turbo Cobras ‘ started by badcobraJul 27, Jul 27, 1. It was so easy, I thought I would share how I did it. I know many run this boost controller and you may not know how easy this is to set up. I have read others using micro-switches, and this was WAY easier.
All you have to do is hook up two different wires and ground two other wires, configure the eboost and that’s it. Hopefully this is helpful to someone.
I have no idea how to duplicate this with other boost controllers. Why would you want to run boost by gear?
It allows you to ramp boost in based on what gear you are in. If you have trouble running 20lbs in first gear and getting traction, now you can run less in 1st, a little more in 2nd, ebost2 hopefully all the boost in high gear. I do not use a transbrake.
Why does manal matter? Because I bought the shift ball with a ebooxt2 switch in it that many use to activate a transbrake. If you were using this button to activate a transbrake, you would have to fashion up some other button that you can depress during gear shifts or use for the brake. If you have a manual trans, this same process would work just as well. You could buy a shiftball with a button and do the exact same thing.
Electronic Boost Controller (EBC) TURBOSMART eBoost2 66mm | ,00 € |
On the eboost2 wiring harness that is probably tucked under your carpet or dash, there are some wires eboost are not connected to anything.
Specifically you are looking for the green wire and the orange wire. Hooking the eboosy2 wire up to the shift knob switch allows you to move up set points with each press of this button. Each set point will need to be configured to have a different higher duty cycle and gate pressure.
Prior to this, you will have to go into the nSP menu and configure the number of set points.
Since I have 3 gears, I will have 3 different set points. Hooking the orange wire to another switch allows you to move down set points with each press of the button. All you are doing when pressing either button is grounding the wire. I then stopped by home depot for a little roll of 16ga wire and some manuall connectors.
First things first, I removed my center console as I had to manuak a hole for the little switch on my shifter plate. I then measured how long of wire I would need from this switch to reach the orange wire and made it extra long. I stripped the wire on both ends and proceeded to solder a wire directly to both of the posts on the switch. Once completed with that, I finished installing the ehoost2 in the center console and then reinstalled it in the car.
I strung that wire to where the eboost2 harness was under passenger carpet on my car. Next I screwed the new shift ball in and ran that wire to the same spot. Next, I stripped the green and orange wires on the eboost harness. I thought about soldering these connections also, but it seemed rather silly if I ever had to remove the center console again.
The ebost2 from the shifter ball I hooked to the green wire. On the small push button, I hooked up one wire to the orange wire on the eboost harness. I then grounded the remaining wires from the shifter ball and other pushbutton switches. You must maanual these two wires. This will take some effort to get all dialed in.
Might be best sboost2 jot down what set point makes what boost level.
You will also have to turn on switch logic and set to setting SSB. Consult the manual, it’s all in there. Overall this is very easy to do. I wish I would have done it years manusl. My total time on this project is maybe 1 to 1. This is what it looks like in the car, and a short video description.
Electronic Boost Controller (EBC) TURBOSMART eBoost2 66mm
Jul 27, 2. Jul 27, 3. Jul 28, 4. I definitely need this. Thanks for he write up! Mar 15, 5. I made a video describing how this works. Hopefully some manuxl you guys with the eBoost2 can get some time and set this up, it is so easy to do.
Eboost2 boost by gear how to
You must log in manuzl sign up to reply here. Share This Page Tweet. Your name or email address: Do you already have an account? No, create an account now. Yes, my password is: Search Forums Recent Posts.