DRAFT. prEN August ICS Will supersede EN English Version. Testing fresh concrete – Part 1: Sampling and common. EUROPEAN STANDARD FINAL DRAFT NORME EUROPÉENNE prEN EUROPÄISCHE NORM June ICS Will supersede EN. BS EN Testing fresh concrete. Sampling (British Standard) This European Standard specifies two procedures for sampling fresh concrete by.
|Published (Last):||28 July 2013|
|PDF File Size:||1.56 Mb|
|ePub File Size:||10.46 Mb|
|Price:||Free* [*Free Regsitration Required]|
Gently press the concrete around the TMD at the surface of concrete so that the ambient temperature does not influence the reading. A sample of concrete is placed in a mold, shaped as the frustum of a cone, and compacted.
Dn Similar Items This product falls into the following categories. By continuing to use this website, you agree to their use.
BS EN 12350-1:2009
This test is considered applicable to: This document is not a European Standard. Wash wet concrete off the skin immediately. Ways of how the sample shall be vibrated: It is subject to change without notice and shall not be referred to as a European Standard.
Log In Sign Up. Self-compacting concrete – Slump-flow test in preparation ; Part 9: Already Subscribed to this document.
BS EN – Testing fresh concrete. Sampling – BSI British Standards
The time for this to occur depends on the concrete temperature, cement type, mix proportions, the use of admixtures with set retarding properties and consistency of the concrete.
These limits are sufficient for normal UK temperatures. Notify me of new comments via email.
In the case of self-compacting enn, the mould shall be filled in one operation and no eb compaction shall be applied during filling or after the mould is filled. Scope This practice specifies methods for making and curing test specimens for strength tests.
Standards Subsctiption may be the perfect solution. Worldwide Standards We can source any standard from anywhere in the world. Scoopfuls are taken from four different parts of the load to form the standard sample.
NOTE The requirement for remixing the sample before tests on the fresh concrete, or before making test specimens, is included in the relevant standards. Deposit the increments into the container s. Frequency shall be at least vibrations per minute The diameter dn the internal vibrator not exceeding one-quarter of the smallest dimension of the test specimen Vibrating table with a minimum frequency of 40 Hz 2 cycles per minute Compacting rod or bar Preparation and filling of the moulds Before filling the mould, cover the inner surface of the mould with a thin film non-reactive release material to prevent 123350-1 concrete from adhering to the mould.
Avoid over-vibration, which may cause loss of entrained air. You may delete a document from your Alert Profile at any time. Scope This standard covers the determination of the temperature of freshly mixed hydraulic-cement concrete. Pressure methods BS EN Raise the mold carefully in a vertical direction with no lateral or torsional motion Raise the mold rn 2 to 5 sec. Now, if the placement of concrete goes beyond these waived time limit, the concrete should be rejected.
Mechanical vibration using Compacting with an internal vibrator Apply the vibration for the minimum duration necessary to achieve full compaction of the concrete.
Testing fresh concrete -Part 1: Sampling | Daniel Stănică –
Complete the temperature measurement within 5 min except for concrete containing the coarse aggregate of a nominal maximum size greater than 75 123350-1 which may require up to e min for the transfer of heat from the aggregate to the mortar. Deposit the increment s in the container.
As the load is discharged, sampling should be taken from the whole width and depth not just the top part. When mixing and sampling of concrete is done in a laboratory, different procedures may be required. If the tamping operation of the top layer results in subsidence of the concrete below the top edge of the mould, add more concrete to keep an excess above the top of the mould at all times.
Strike off eb mold with the tamping rod in a screeding and rolling motion Remove concrete from the area surrounding the base em prevent interference with the movement of slumping concrete.
Concrete cubes at the site Marking The test specimens shall be marked clearly and indelibly, without damaging the specimen using a cub tag that contains the information related to the specimen Casting date, ticket number, specimen 1250-1, location of sampling…. Rod the second and top layers throughout their depth, so that the strokes just penetrate into the immediately underlying layer. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.
You are commenting using your WordPress. Self-compacting concrete – J-ring test in preparation. Create a website or blog at WordPress. The Location of concrete represented The Time of casting Compacting Methods Internal Vibrators that will be used should have the following specs: The following amendments have been made to the een of this standard: Take the scoopfuls of concrete through the moving stream from the truck mixer. The vertical distance between the height of the mould and the highest point is measured and recorded as the slump in mm.
Marking The test specimens shall be marked clearly and indelibly, without damaging the specimen using a cub tag that contains the information related to the specimen Casting date, ticket number, specimen ID, location of sampling….